Skip to main content

Bangladesh · 2020

A 90 × 70 Upright Line Running Since 2021

Two containers to Bangladesh in January 2020, uprights in production since early 2021, and no roll change beyond routine maintenance. What kept it running.

See the machine
Market
Bangladesh
Delivered
2020
Customer
A pallet racking manufacturer
Main machine
Rack Upright Roll Forming Machine

Two containers of upright line were loaded in January 2020 for a racking manufacturer in Bangladesh. The machine has been producing pallet racking uprights since early 2021, and has stayed in production without a roll change beyond routine maintenance. That second sentence is the interesting one.

Why 90 × 70

90 × 70 is the workhorse upright section for medium-duty pallet racking: 90 mm face, 70 mm flange, formed from 1.5–3.0 mm coil. The face width sets how the beam hook engages; the flange width sets the frame bracing spacing.

A plant running 90 × 70 as its standard section can serve most of a local market without a second roll set, which is why it is the most common first upright line we build. It is not the biggest section anyone makes — it is the one that covers the most orders per roll set.

What an upright has to get right

The upright is the vertical member of the frame and carries the entire load of the bay down to the floor. Whatever the section, three things have to be right before a rack can be assembled:

  • Face and flange dimensions — the face sets beam hook engagement, the flange sets bracing spacing.
  • Hole pattern — tear-drop and butterfly holes are punched so the beam connector seats and locks. The pitch has to be identical on every upright, or the beams sit at different levels.
  • Straightness — a bowed upright will not stand plumb, and a frame out of plumb cannot be forced straight without stressing the bracing.

On this class of line the thickness runs up to 3 mm. Above that the machine changes rather than the setting: station count and motor size go up, because a 3 mm Omega section takes a different forming schedule from a 1.5 mm one.

Punched in line, not after

Holes can be punched in line, between the feeder and the forming machine, or off line on a separate press after cutting. This line punches in line, with the press integrated into the sequence.

In-line punching keeps every upright in a batch in register with its own cut length and removes a handling step per piece. Off-line is cheaper on capital, but it adds a press, an operator and a position error that has to be controlled at the press rather than at the line. On a line running a regular hole pattern at production speed, in-line is normally the better economics — not because it is faster, but because the hole pattern is the feature the entire racking system depends on.

Why it has stayed in production

A forming line that runs for years without intervention is not an accident. It comes from three things.

The leveler takes coil set out before the rolls. The guide is set correctly, so a light-to-medium strip does not walk. And the roll gaps are recorded at commissioning, so a change of coil hardness is corrected by returning to a known setting rather than by trial and error on the machine.

The third one costs nothing at the time and saves the most later. A plant that has the commissioning sheet can put a new coil on and be back in tolerance in fifteen minutes. A plant that does not has to rediscover the setting, and usually overshoots it twice before getting there.

The line as built

18 forming stations, 15 kW main motor, GCr15 rollers and 40Cr shafts at 15 m/min, with a separate hydraulic cutting station. The line was assembled, run on production coil, and the sample checked for section dimensions, hole pitch, hole-to-edge distance and straightness over a full 6 m length before it was broken down into two containers.

The numbers

Section
90 × 70 mm
Strip
1.5–3.0 mm
Containers
2
In production
since 2021

What was in the line

  • Rack Upright Roll Forming Machine

    Rack Upright Roll Forming Machine

    Rack Upright Roll Forming Machine (also called Omega-Racking Upright Roll Forming Machine) is used to produce rack upright for Warehouse Pallet Rack

    View machine

18 forming stations, 15 kW main motor, punched in line; shipped in two containers.

Tell us the profile and we will size the line

Section drawing, strip thickness, material grade and the output you need per shift — that is enough for us to come back with a machine specification and a price.

WhatsApp us